-
Machine Compatibility: 5, 6, 7 Not suitable for: EMERALD series, EDEN ROSE 250M, TRIBUTE 140M and 145M Not sure which group your machine belongs to? Check out the Machine compatibility chart The Dual Feed Foot with changeable presser feet is designed to feed layers of fabric and/or batting evenly. It is perfect for quilting, sewing velvet, stretch fabrics, imitation leathers, and fabrics that need precise pattern matching. Snap-on the Changeable Straight Stitch Foot. Select the center needle straight stitch. Adjust it up to a maximum stitch length of 6. Snap-on the Changeable Zigzag Foot and select stitches up to a maximum of 7mm wide and 6mm long. How to use: Remove the presser foot ankle by unscrewing the ankle screw. Place the Duel Feed Foot onto your machine from the back, positioning the fork over the needle clamp screw. Screw the Dual Feed Foot onto the presser foot bar with the presser foot ankle screw. Reduce presser foot pressure to 3. Snap-on and remove the changeable presser foot: With presser foot bar in the up position, place the presser foot under the Dual Feed Foot. Push the changeable foot upwards so that it snaps into place. To remove the changeable foot, push the front of the foot upwards until the foot snaps off. How to attach the guide: The two guides included with the Dual Feed Foot will help you sew parallel rows of stitching side by side as in channel quilting or tucking. There is one guide for the left side, and one for the right. Insert the guide into the hole in the back of the dual feed. Adjust the space between the foot and the guide by pulling it to the left or to the right.
-
Suitable for S25 and S21 Overlockers The Taping Foot is used to apply seam tapes to seams to prevent stretching. It is especially good for stabilizing shoulder seams. With this foot you can reinforce and construct seams in one step.
-
Suitable for HUSKYLOCK™ S25 and S21 and AMBER™ AIR s|600 Overlockers With the Stap and Belt Loop foot, create straps and belt loops easily using a cover stitch. Just put a strip into the foot and the strip is folded automatically and stitched in place. How to use: Set the machine for a Coverstitch wide. Use the default stitch settings. Adjust if needed. Cut a strip of fabric 1" (25mm) wide. Cut the top corner of the strip at a 45 degree angle to form a point. Insert the cut angle into the guide, right side of the fabric facing up. Pull strip through the slot and under the foot. Extend the tail of the strip behind the foot. Use a tweezers to feed the strip into the foot if needed. Snap the Strap and Belt Loop foot into the machine. Slide the strip approximately 2" (5cm) behind the foot. Lower the presser foot. Be sure both raw edges of strip are turned under before stitching. See the first few stitches. Stop and clip the needle threads close to the presser foot and continue sewing. For even feeding, hold the fabric strip slightly below the first guide in the front of the foot. Sew at medium speed. Check the fabric as you sew to ensure proprt feeding. Note: Sew the folded fabric strip without additional fabric underneath to create straps and belt loops or sew the folded strip onto another fabric for decorative effects.
-
Suitable for S25 and S21 Overlockers With the Piping Foot with Cording Guide, you can create piping, corded tucks and decorative trims. Easily create your own piping: Set the machine for Chainstitch. Use the default stitch settings. Adjust if needed. Note: Although the machine recommends needle D, you will use needle E for this technique instead. Snap on the Piping foot. (The cording guide is not used for this technique.) Place the cord in the groove on the bottom of the foot and pull the cord tail behind the foot about 2½” (5cm). Note: ¼” - 5/8” (1.5 - 2.0mm) cord can be used. Cut a strip of fabric on the bias, 1” (25mm) wide. Wrap the fabric around the cord in the front of the foot. Slide the fabric under the foot. Lower the presser foot and sew over the cord and fabric (illustration 1). (Hold the cord behind the foot as you begin to sew.)
-
Microtex or sharp needles (H-M) have a sharp point like Denim needles but are available in smaller sizes. Use for microfiber to topstitch lightweight tightly woven fabrics.
-
Microtex or sharp needles (H-M) have a sharp point like Denim needles but are available in smaller sizes. Use for microfiber to topstitch lightweight tightly woven fabrics.
-
Suitable for S15 Overlocker This foot is used for sewing lace and/or borders together or onto the workpiece
-
Suitable for HUSKYLOCK™ S25 and S21 and AMBER™ AIR s|600 Overlockers Use the Join and Fold Edging Foot to hem the fabric edge and attach it at the same time. Set the machine for Coverstitch. Adjust if needed Use the default stitch settings. Adjust if needed. Snap-on the Join and Fold Edging Foot. Slide the raw edge of the fabric right side up, into the fabric guide. Slide the fabric to the back underneath the presser foot and needles. Insert the lace into the right lace guide and pull a lace tail about 1" (2.5cm) behind the foot. Use tweezers if needed. Lower the presser foot. Hold the fabric in your left hand and lace in your right hand and start to sew. Note: Adjust the screw on the guide to adjust the stitch position if needed.
-
Suitable for HUSKYLOCK™ S25 and S21 and AMBER™ AIR s|600 Overlockers The Flat Trim Foot makes it easy to add lace and trims to the top of the fabric with a coverstitch to create beautiful decorative edges and effects. How to use: Set the machine for Coverstitch wide Snap on the Flat Trim Foot Use default stitch setting. Adjust if needed. Insert the fabric edge into the lower section on the left side of the foot and under the needles. Insert the trim into the upper section on the right side of the foot. Slide the trim toward the back of the foot beyond the needles, leaving a short tail of trim behind the needles. Tip: Use tweezers to slide the fabric and the trim to the correct position under the needles. Lower the needles into the trim and the fabric. Lower the Flat Trim foot As you sew, hold the fabric in your left hand and the trim in your right hand. Tip: If you want a finished fabric edge, press a 1/4"(6mm) hem to the right side of the fabric before inserting the fabric into the Flat Trim Foot. The lace will cover the fabric raw edge when sewn in place
-
Denim needles (H-J) have a sharp point to penetrate tightly woven fabrics without deflecting the needle. For canvas, denim and microfibers
-
Suitable for S25 and S21 Overlockers Increase your visibility while sewing with the Clear Coverstitch Foot. Create beautiful decorative edges and effects with the Flat Trim Foot and the Join and Fold Edging Foot. Straps and belt loops are effortless to create with the Strap and Belt Loop Foot. Add piping, corded tuck and even create wonderful decorative trims with the Piping Foot with a Cording Guide.
-
Suitable for HUSKYLOCK™ S25 and S21 and AMBER™ AIR s|600 Overlockers The three-fold 3/8" (10mm) binder will turn a lightweight knitted fabric strip into a binding and attach it to the project edges all in one step. To bind edges with 3/8" (10mm) Coverstitch Binder, cut a 11/8" wide strip of lightweight knit fabric, such as light weight jersey or interlock.
-
Sewing a decorative wavy edge with the Corded Wavy Edge Foot is easy. The curvy, softly ruffled edge is a perfect finish for bridal veils, figure skating costumes, ballet skirts, crafts and more. Note: For best results, use fabric with stretch. For fabric with no stretch, cut on the bias. How to use: Set the machine for a 3-thread rolled edge. Snap-on the Corded Wavy Edge foot. Insert a 0.3mm nylon fishing line (or similar) into the opening in the foot. The fishing line will be covered by the rolled edge. Start to sew slowly. Make sure the fishing line is hidden in the rolled edge as you sew. Tip: * 40 wt. rayon embroidery threads in a contrasting colour in the upper and lower loopers will give a shiny colourful edge.
-
Suitable for HUSKYLOCK™ S25 and S21 and AMBER™ AIR s|600 Overlockers With the Clear Coverstitch Foot, you can see your fabric and marked line under the foot as you sew. How to use: Set the machine for a Coverstitch or a Chainstitch. With a water-soluble marker, draw a line on the fabric to mark the stitching line. Snap-on the Clear Coverstitch foot. Use default stitch settings. Adjust if needed. Place the fabric under the presser foot and the needles. Start to sew into the fabric without chaining off first. Use the red centre marking on the foot as a guide as you follow a line drawn on the fabric. The Clear Coverstitch foot will give you a great view of the marked line and of your fabric while sewing.
-
Suitable for S25 and S21 Overlockers The Blindhem Foot is perfect for sewing invisible hems and for applying lace. The hem is sewn, overcast, and trimmed in one step.
-
Suitable for S15 Overlocker The Blindhem Foot is for sewing cuffs on knit fabrics, and hemming where you want the seam to be invisible.
