-
Suitable for S15 Overlocker This foot is used for sewing lace and/or borders together or onto the workpiece
-
Microtex or sharp needles (H-M) have a sharp point like Denim needles but are available in smaller sizes. Use for microfiber to topstitch lightweight tightly woven fabrics.
-
Microtex or sharp needles (H-M) have a sharp point like Denim needles but are available in smaller sizes. Use for microfiber to topstitch lightweight tightly woven fabrics.
-
Suitable for S25 and S21 Overlockers With the Piping Foot with Cording Guide, you can create piping, corded tucks and decorative trims. Easily create your own piping: Set the machine for Chainstitch. Use the default stitch settings. Adjust if needed. Note: Although the machine recommends needle D, you will use needle E for this technique instead. Snap on the Piping foot. (The cording guide is not used for this technique.) Place the cord in the groove on the bottom of the foot and pull the cord tail behind the foot about 2½” (5cm). Note: ¼” - 5/8” (1.5 - 2.0mm) cord can be used. Cut a strip of fabric on the bias, 1” (25mm) wide. Wrap the fabric around the cord in the front of the foot. Slide the fabric under the foot. Lower the presser foot and sew over the cord and fabric (illustration 1). (Hold the cord behind the foot as you begin to sew.)
-
Suitable for HUSKYLOCK™ S25 and S21 and AMBER™ AIR s|600 Overlockers With the Stap and Belt Loop foot, create straps and belt loops easily using a cover stitch. Just put a strip into the foot and the strip is folded automatically and stitched in place. How to use: Set the machine for a Coverstitch wide. Use the default stitch settings. Adjust if needed. Cut a strip of fabric 1" (25mm) wide. Cut the top corner of the strip at a 45 degree angle to form a point. Insert the cut angle into the guide, right side of the fabric facing up. Pull strip through the slot and under the foot. Extend the tail of the strip behind the foot. Use a tweezers to feed the strip into the foot if needed. Snap the Strap and Belt Loop foot into the machine. Slide the strip approximately 2" (5cm) behind the foot. Lower the presser foot. Be sure both raw edges of strip are turned under before stitching. See the first few stitches. Stop and clip the needle threads close to the presser foot and continue sewing. For even feeding, hold the fabric strip slightly below the first guide in the front of the foot. Sew at medium speed. Check the fabric as you sew to ensure proprt feeding. Note: Sew the folded fabric strip without additional fabric underneath to create straps and belt loops or sew the folded strip onto another fabric for decorative effects.
-
Suitable for S25 and S21 Overlockers The Taping Foot is used to apply seam tapes to seams to prevent stretching. It is especially good for stabilizing shoulder seams. With this foot you can reinforce and construct seams in one step.
-
The Beading foot smoothly guides beads and pearls through a channel on the foot for the easy application on garments or crafts.
-
The Beading foot smoothly guides beads and pearls through a channel on the foot for the easy application on garments or crafts.
-
The Blindhem & Lace Foot is great for sewing invisible hems and applying lace. The hem is sewn, overcast and trimmed in one easy step.
-
The Blindhem foot is for sewing cuffs on knit fabrics, and hemming where you want the seam to be invisible.
-
The Clear Coverstitch foot, allows you to see your fabric and the marked line under the foot as you sew.
-
Sewing a decorative wavy edge is easy with the Corded Wavy Edge Foot and your overlock.
-
The Three-Fold (10mm) binder will turn a lightweight knitted fabric strip into a binding and attach it to the project edges all in one step.
-
Create more with your PFAFF® coverlock™ 3.0/4.0 machine with the exciting Inspira® Coverlock Kit.
-
The Elastic foot is great for sewing activewear, lingerie and other elastic insertion techniques.
-
The Elastic foot is great for sewing activewear, lingerie and other elastic insertion techniques.
-
This foot is most suited for gathering when sewing tiered skirts, yokes, cuffs, and frills on skirts and more.
-
This foot is most suited for gathering when sewing tiered skirts, yokes, cuffs, and frills on skirts and more.
-
This foot is used for sewing lace and/or borders together or onto the workpiece.
-
The Piping foot is perfect for inserting packaged piping into seams and on edges for a tailored finish.
-
The Piping foot is perfect for inserting packaged piping into seams and on edges for a tailored finish.
-
Machine Compatibility: admire™ air 7000, coverlock™ 4.0 and 3.0 Create piping, corded tucks and decorative trims with the Piping Foot with Cording Guide. How to insert piping: Set the machine for Chainstitch. Use the default stitch settings. Adjust if needed. Note: Although the machine recommends needle D, you will use needle E for this technique […]
-
Create straps and belt loops easily with the Strap and Belt Loop foot on your coverlock™.
Servicing Canberra and the surrounding regions since 1977.We service and repair all makes and models.
